By Origin:

  • USA (21)
  • By Price Range:

    Need Help? Give us a call or click for live chat.
    1-800-521-3420 Store Hours
    Live Chat

    Suburban Tool, Inc.

    Show:
    Page 1 2 of 2 | Next
    Order By:
    View: Grid | List
    Minute angle step 0.2 is built into gage block roll, eliminating step in base plate. Two hardened and ground side rails and one locking strap included. Strap always remains below top surface. Large hinge pins for extra strength. Notes on Order No. 1701-0025: This item's weight exceeds the UPS…
    $530.10 - $1561.70
    High quality, fine grained, stress relieved cast iron. All ends machined square and parallel to .002 per 6 inches. Extra thick, ribbed construction.Square and parallel within .0005 inch per 6 inches on two faces only. Shipping Notes on Order No. 1701-0705: This item's weight exceeds the UPS…
    Related Items: Angle Plate | Parallels
    $69.15 - $1047.60
    Parallel, square and central to within .0002 inch. Each block comes with one clamp. Made of steel hardened to Rc 58-62. Sizes other than those listed available by special order.
    Related Items: V Block | Parallels | V-block
    $208.70 - $2352.25
    Provides quick, accurate and direct means for setting or checking angles. Eliminates calculations to help avoid errors. Blocks in 1-degree increments to 5 degrees; then 5-degree increments to 30 degrees. By adding the optional 1/4 and 1/2-degree blocks, nearly any angle can be set in 1/4°…
    $33.10 - $296.85
    Designed to be clamped to table of surface grinder or another machine. Top plates laminated from 1/8-inch steel and 1/16-inch stainless and furnace brazed to form one piece. Sealed against dirt and liquids. Maximum holding power achieved when workpiece(s) cover greatest number of north and south…
    $1109.40
    item # 1701-0560
    Chuck has ceramic magnet for superior holding power and is lubricated and sealed against dirt and liquids. Steel compound sine plate hardened to Rc 58-62. Gage block roll has two 0.200 minute steps for setting small angles with standard gage block sets. Tolerance of .0002 and .0003 in squareness,…
    Related Items: Sine Plate
    $2818.80
    item # 1701-0150
    High quality, fine grained, stress relieved cast iron. Four faces and ends machined square and parallel within .002 per 6 inches. Clamping slots for easy workpiece mounting. Shipping Notes on Order Nos. 1701-0790, 1701-0795, 1701-0800: This item's weight exceeds the UPS shipping standard; therefore…
    $118.00 - $492.50
    Ideally suited for holding magnetic workpieces on ID grinders and other machinery that requires a rotating chuck. Permanent ceramic magnet has superior holding power and never loses strength. No electrical controls or collector rings required. Thick top plate is laminated from steel and stainless…
    $646.75 - $5145.15
    Made of steel hardened to Rc 58-62 and ground in matched pairs on four sides, for use where extra precision is required. Matched in size on width and height to tolerance of ±0.0002 inch on 6-, 8- and 12-inch lengths, and 0.0003 inch for larger lengths. Total parallelism, straightness over the…
    Related Items: Parallels
    $169.80 - $2200.65
    Powerful alnico magnet and on/off switch. Top, bottom and end magnetize simultaneously. Precision ground flat, square and parallel to overall .0005-inch accuracy. Bottom surface relieved .125 to minimize magnetism loss. Model MTC-LFP has 3/16 x 1/16 inch fine pole construction for holding small or…
    Related Items: Magnet
    $471.80 - $1412.65
    All chucks havee ceramic magnets for superior holding power and are lubricated and sealed against dirt and liquids. Removable on/off handle, locking strap, and two rails included. Sine plate is steel hardened to Rc 58-62. Squareness, parallelism and roll center distances between .0002 and .0003…
    Related Items: Magnetic Block | Sine Plate
    $1222.35 - $2755.35
    High quality, stress relieved cast iron. All faces and ends finished square and parallel. Size tolerance, ±.015 inch. Ground finish is square within .0005 per 6 inches and parallel .0025 per 6 inches.
    Related Items: Angle Plate
    $273.50 - $776.35
    Showing item 1 - 12 of 21 items found
    Site Search by  Site Search powered by SLI Systems