One piece, ebony black oxide construction. Thread with your drill press, lathe, milling machine, etc. 2-inch length. Available individually or as a three-piece set.

Related Searches: Lathe Die Holder | Mill Drill Lathe | Lathe Tool Holder

Click to View all SKUs

Click to View Less SKUs

0513-0004 - * Die Diameter: 13/16" * OAL: 2" * Pieces: 1 * Shank: 1/2"	$9.95
0513-0006 - * Die Diameter: 1" * OAL: 2" * Pieces: 1 * Shank: 1/2"	$9.95
0513-0007 - * Die Diameter: 1-1/2" * OAL: 2" * Pieces: 1 * Shank: 3/4" 3/4"	$11.95
0513-9980 - * Die Diameter: 13/16", 1", 1-1/2" * OAL: 2" * Pieces: 3-holder set * Shank: 1/2", 3/4"	$25.95

This quick-change 2MT tailstock unit is supplied with three heads; 1/2-inch capacity chuck with key; live center; 1-inch outside diameter die holder; one 2-3MT drill sleeve; and two drill drifts. Chuck Size: 1/2" w/key Taper: 2MT

Related Searches: Tailstock | Quick Change Lathe | Lathe Centers

Cut threads on any lathe fitted with a Morse taper tailstock Improves thread quality with fewer part rejections over hand-held method Four to five times faster than threading with a single point tool Reduces chance for operator injury Heads or shanks available separately; see description below for…

Related Searches: Lathe Die Holder | Lathe Tools | Tailstock

Click to View all SKUs

Click to View Less SKUs

0513-0050 - * Fits Die OD: 1" * Fits Head Number: ---- * For MT: 2 * Head Number: FDH1-2 * Max Thread Length: 2-3/8" * Shank: ---- * Type: Head	$56.50
0513-0055 - * Fits Die OD: 1" * Fits Head Number: ---- * For MT: 3, 4 * Head Number: FDH1-34 * Max Thread Length: 3" * Shank: ---- * Type: Head	$67.00
0513-0060 - * Fits Die OD: 1-1/2" * Fits Head Number: ---- * For MT: 3, 4 * Head Number: FDH15-34 * Max Thread Length: 3" * Shank: ---- * Type: Head	$67.00
0513-0065 - * Fits Die OD: 2" * Fits Head Number: ---- * For MT: 3, 4 * Head Number: FDH2-34 * Max Thread Length: 3" * Shank: ---- * Type: Head	$74.00
0513-0070 - * Fits Head Number: FDH1-2 * For MT: 2 * Shank: FDHS-2T * Type: Shank	$55.50
0513-0075 - * Fits Head Number: FDH1-34, 15-34, 2-34 * For MT: 3 * Shank: FDHS-3T * Type: Shank	$74.00
0513-0080 - * Fits Head Number: FDH1-34, 15-34, 2-34 * For MT: 4 * Shank: FDHS-4T * Type: Shank	$86.25

…steel set comes in a plastic case and contains the following: Tap and die sizes 4-40, 6-32, 8-32, 10-24, 10-32, 12-24, 1/4-20, 1/4-26, 5/16-18, 5/16-22, 3/8-16, 3/8-20, 7/16-14, 7/16-18, 1/2-12, 1/2-16 (BSW) and 1/8-28 (BSP). Die holder Tap wrench T-type tap wrench Screwdriver

Related Searches: Tap And Die | Tap Set | Tap Die Set

…Stem is hard chrome plated. Contact point is hardened ground chrome plated steel. Holder is a universal magnetic base that will save time and improve accuracy. Strong magnet with 45 pounds of holding power. Zinc die cast housing and five different locations for mounting accessories. Three positions…

Related Searches: Mighty Mag | Dial Indicator | Tap Die Set

Click to View all SKUs

Click to View Less SKUs

1267-0075 - * Dial Diameter: 2" * Graduations: .001" * Pull (lbs): (Base) 45 lbs. * Reading: 0-100 * Type: Indicator & USA magnetic holder	$19.95
1267-0080 - * Dial Diameter: 2" * Graduations: .001 * Pull (lbs): (Base) 45 lbs. * Reading: 0-100 * Type: Indicator & WT Import magnetic holder	$15.95

…-20, 1/2-13, 1/2-20, 3 x .5, 4 x .7, 5 x .8, 6 x 1.0, 8 x 1.25 20 1-inch outside diameter round dies (same sizes as taps) Five screw extractors in sizes #1, #2, #3, #4, #5 1-inch outside diameter die holder #5 tap wrench T-handle tap wrench SAE screw pitch gage Metric screw pitch gage Storage case Type…

…Heavy-duty grain saddle back leather Extra rivet reinforced tape pocket secures tape rule in place with a pull-through back, safety strap and snap Die molded, one hand "push-up" pocket Extra wide 2.75-inch belt slots

Long considered the “Swiss Army Knifeâ€Â� of the industry, Edwards Manufacturing's ironworkers are do-all machines that punch, shear, notch and brake mild steel plate, bar stock and angle. A wide range of accessories is available to fabricate rod, square stock, sheet metal and pipe.…

Related Searches: Ironworker | Foot Shear

Click to View all SKUs

Click to View Less SKUs

2796-0030 - * Angle Shear: Max. size, 3" x 3" x 3/8"; 4" x 4" x 1/4"; cycle time, 1/2" x 2" shear, 2 sec. * Bar Shear: 1-1/8" rounds & squares; 3/4" x 4" flat max. thickness; 1/2" x 12", 3/8" x 14" max. flat width * Base: 41-1/2" x 40" * Height: 57" * Motor: 3 HP, 3 ph., 208/240V * Net Weight: 2,250 lbs. * Punch & Die: Max. 1-1/16" punch; 1-1/4" die; (optional table & holder, 1-9/16" punch; 1-5/8" die * Punch Capacity: 55 tons; max. 1-1/8" dia. 5/8" plate * Stroke: Punch, 1-1/4" * Throat Depth: 7" * Type: Three phase

$6,999.00

2796-0032 - * Angle Shear: Max. size, 3" x 3" x 3/8", 4" x 4" x 1/4"; cycle time, 1/2" x 2", 2 sec. * Bar Shear: 1-1/8" rounds & squares; 3/4" x 4" max. flat thickness; 1/2" x 12" & 3/8" x 14" max. flat width * Base: 41-1/2" x 40" * Capacity: 55 tons * Height: 57" overall; punch, 8-1/8" open, 6-7/8" closed * Motor: 3 hp, 1 ph., 208/240V * Net Weight: 2,250 lbs. * Punch & Die: Max. 1-1/16" punch, 1-1/4" die; (optional oversize table & holder) 1-9/16" punch, 1-5/8" die * Punch Capacity: Max 1-1/8" dia.; 5/8" plate * Stroke: Punch, 1-1/4" * Throat Depth: 7" * Type: Single phase

$7,129.00

A practical shop tool for quick separation of punch and die holders.

Click to View all SKUs

Click to View Less SKUs

6913-0005 - * Length: 18" * Size: 5/8" hex	$11.10
6913-0010 - * Length: 30" * Size: 5/8" hex	$16.35

…into any standard 110-volt outlet Meets ANSI standard B111-5 for ironworker Accommodates optional accessories Punching station is punch ready with die holder, stripper and punch retaining nut 1-gallon oil capacity Power cavity accommodates three-in-one shear (included), plus optional 8-inch brake and custom…

Related Searches: Hydraulic Press